Useful Guide: How to Vacuum a Pool?

Vacuuming your swimming pool is the best way to keep it clean and devoid of debris and dirt. The question is that how to vacuum a pool?

Although it is a hard task to clean all the debris and fight algae with a little effort you can balance the pH of the water and the pool chemicals will work more effectively and your pool will look cleaner and nicer as well.

You can use a multitiered approach to maintain sparkle and can clean the in-ground swimming pool. First, balance the pH and then control the foreign matter debris.

Small particles that are suspended in the pool can be removed by the normal circulation of water via the filter and larger particles i.e. leaves are captured by strainer baskets when water passes through the skimmer net.

Vacuuming is required for contaminants that are set to the bottom of the pool. Always do vacuuming whenever it is needed and recommended rather than sticking to a hard schedule.

Even if you own an automated pool cleaner, you still need a manual vacuum cleaner and this article will guide in this regard.

What Things to do Before Vacuum a Pool?

  • Large or Debris Entfernung

Use a scoop net before you start to vacuum to remove any particularly large leaves or debris that might otherwise obstruct the vacuum head or tube.

  • Connect the vacuum head to the hose pipe and telescopic poles.
  • Water Hose Pipe Flood

Submerge the tub and allow water to flood. This involves removing air trapped in and generating an air block, which may otherwise be drawn into the pump.

Pro Tip: keep the pants near the return outlet to fill the pants with water quickly.

  • Join the pipe in the skimmer or the dedicated suction port

When your swimming pool has a dedicated suction port, add the pipe to it. Don’t hide the skimmer from the pool if your pool doesn’t.

You need to remove the basket with most skimmers so the hose can be attached. At the bottom of the skimmer is the shaft harbor.

  • Swimming Pool vacuum

The vacuum head slowly and consciously passes through the bottom and side of the pool with the telescopic pole.

  • Unplug the Skimmer Hose Pipe or the Dedicated Suction Port:

You can disassemble the vacuum equipment after disconnection.

  • Turn Off the Pump
  • Backwash

Turn the filter valve in the position Backwash. In the sand of a sand filter system, the waste, dirt, and oil are blocked.

The reverse flux reverses the water flow and sends dirty water into the ground or drain by means of a waste line. Turn the pump and re-wash for 2 minutes or until the water runs clear through the visible glass on the filter.

Related Post: 6 Best Bissell Vacuum Buying Guide

Pool Vacuuming Must-Have Following Things

Before vacuuming a pool, you should have everything that is required to perform the job. If you have a pool you must also have a manual pool vacuum.

You can experience many problems that your manual vacuum cleaner cannot clean the algae blooms. For successful cleaning of algae blooms, you just need to shock, use algaecide prior to vacuum cleaning.

Vacuum Head and Telescope

If you own a swimming pool, it is good to have a telescoping pool. Additionally, you must have alternative attachments such as skimmers brushes, and nets.

The vacuum heads of most swimming pools are designed in such a way that they can fit with any telescope pool. On the other hand, a vinyl pool liner needs a vacuum that has been equipped with a soft brush to prevent tears and damage.

But if you have a granite or concrete swimming pool then select a vacuum head that has wheels for easy movement.  

Vacuum Hose

The vacuum hose joins your vacuum head with your pool pump through the skimmer inlet, which provides the power of debris sucking.

Vacuum Plate

The vacuum plate is also called a “skimmer plate” which connects the skimmer inlet with the hose. Once you have all the equipment then follow the below steps to vacuum your swimming pool.

The Stepts of Vacuumimg a Pool

Here are the following steps to vacuum your pool.

First Assemble Your Pool Vacuum

This is an easy and quick method to do. Just attach the head of the vacuum to your telescope pole and it should snap on easily.

The priming of your vacuum by removing all the air is the first thing to do. As air pockets can give your unit loose suction, so release the air pockets before time which will help to keep the pool going longer.   

Connect the Vacuum Hose

Connect the vacuum head to one end of the hose and attach the skimmer to the other end by using a vacuum plate. Keep in mind to take off the skimmer basket first.

While connecting the pool vacuum hose to the skimmer, you must blow all the air out of it. You can notice air bubbles moving up from the vacuum head, permitting you to realize that air is flowing out through the hose.

The easiest and simplest way to blow out all the air is by holding the hose up against one of the jets of your pool and quit until you see no air bubble coming out from the hose.  

Select Filter Valve Setting

You may leave your multiport valve filter labeled “Filter” for light vacuuming. For larger amounts of garbage and longer jobs set your filter system to the “Waste setting” that doesn’t allow you to send water down the drain and sends it via filter paper.

While using the filter of your pool you will notice that the water level of your pool is dropping. You should use a garden hose to keep your pool adequately filled and ensure a steady stream of fresh water and keep an even water level.   

Start Vacuuming

Now start vacuuming for which you just need to move the vacuum head back and forth along the pool surface until it got clean. If suction is losing you can repeat steps 1 and 2.

Move your vacuum in a slow linear way like a real vacuum on a blazer (moving too fast will just stir up the dirt without sucking it up). You may have to stop and empty the pump strainer before continuing when the pool is particularly dirty.

Remove all the debris from your floor as many times as necessary.

Detach, Change Filter Settings, Do a Final Cleanup

You can disconnect your vacuum head and flakes when your pool is emptied to your satisfaction. Make sure that the skimmer’s bottom is also clear.

When your pump settings have changed, make sure that you change them back and (now it is the right time to do a quick backwash if you are using sand or DE filter).

Place a brush on the telescoping poles and give a good scrubbing of the bathroom and the sides. To ensure that your pool water remains balanced, test your water after you vacuum your pool.

You will know what we are talking about when you’ve ever seen your robotic pool cleaner slip a pile of floating floats on from one end of your pool to the other: robotic pool cleaners are excellent for daily maintenance, lighting, but they’re not for heavy lifts.

If waste is not immediately removed, its quality can wreak havoc and lead to maintenance problems such as algae. A pool vacuum does short work with heavy waste that helps you to maintain your pool clean and invites you to avoid headaches.

Related Post: How to Clean a Vacuum Cleaner?

How to Vacuum a Pool with a Garden Hose?

A vacuum system that attaches to your garden hose is also used to vacuum the pool. For smaller pools or hot tubs, this approach is well cost-effective. You just have to take these simple steps for this method:

  1. Connect the telephoto poles to the head of the vacuum.
  2. Connect the bottom of the pin to the other end. (It should connect to its spigot on the other end of your hose).
  3. Add the vacuum bag to the right vacuum opening.
  4. Turn the filtration system of your pool off.
  5. Turn the water into the pool and plunge into the vacuum.
  6. Drag your vacuum slowly and steadily back and forth across the surface to vacuum the pond and clear dirt and waste.
  7. Pull out the vacuum and empty the collection bag when your vacuum loses suction during this process.
  8. If this does not work, attempt to turn the source of water off and then turn it on again before it is reduced to the pool water.
  9. Then turn on the filtration system to remove any floating waste.

Note: Don’t hurry up through this job and remove the waste at the bottom of the pool. Your vacuum can’t clean it when this happens, it floats about for a while and will settle down again later. Take the time to cover the whole surface of the pool thoroughly and slowly.

How to Sand-Filter Your Pool?

You simply have to choose the right setting if you choose to use a sand filter as your vacuum filtering method. Six settings are typically used for this type of filter system:

  1. Rink
  2. Recirculate
  3. Rinse
  4. Waste
  5. Filter, or
  6. closed

The filter setting is the most common environment in which a pool is vacuumed. There are no visible algae that handle minimal debris.

Related Post: 7 Best Commercial Vacuums of 2021

After Vacuuming Your Pool

After your bowl has been cleaned, remove the vacuum head and draw any water in the vacuum tube. Join the cleaning brush to the pole and wipe off all algae, dirt, and waste from the sides of the pool.

Clean out any debris in your filter pump and return the filter to a final wash when you’ve got the “Filter” setting and a multiport system.

Using the ‘Waste’ setting to vacuum the pool, ensure that the valve is switched back to the filter setting and add fresh water to your pool until the water level has been restored.

Rinse and re-store all your equipment with fresh water. This helps to keep it working well and prevents unnecessary wear and corrosion.

The vac head you mustn’t be afraid of! When the time comes to vacuum your pool, whether it’s a handy one or a war on invading algae, you can make the effort with a little preparation and a lot of elbow grass.

If you don’t want to vacuum your swimming pool with an automated vacuum cleaner, you can use a number of other pool cleaners.

Robotic Pool Cleaner

Independent cleaners that use electricity to vacuum your pool. You plug it in, put it into your pool, and let it do all its hard work on its own.

All you have to do when they get full of debris is empty the integrated filter bag. These are by far the best pool cleaners available on the market but can be a bit more expensive. Hey, what you’re paying for.

Pressure-Side Pool Cleaners

These cleaners hook up on your return line to power a self-contained automatic cleaning agent around the bottom of your pool to collect waste to the filter bag by pressing the water from your filter system.

Suction Side Pool Cleaner

This is only an automatic version of manually vacuuming your pool. When you vacuum your pool manually, they crochet in the same way.

However, the biggest difference is that you move around the bottom of your pool. So, you don’t have to stand and perform it yourself in the hot sun.

However, we would recommend that you take a press-side or robotic cleaner if you are going to make this investment.

Conclusion

Vacuuming your pool once a week is a good idea. When you notice large amounts of waste, dirt, or leaves on the floor of the pool, you should vacuum your pool (for example, your pool may need vacuuming after a heavy storm).

By using different methods of vacuum cleaning, you can clean and vacuum your pool and can save time. I hope this article “how to vacuum a pool” is very helpful for you.

If you want to know more about cleaning visit our website.

Leave a Comment